Contents

## What is the actual height of a 10 tall plate line wall?

Occasionally, you see a ceiling height in North America of 10′, and Figure 4 shows how a wall for this ceiling height would be framed. The actual height of an 10′ ceiling is 10′ 1/2″ = 121.125″-0.625″, measured from the subfloor.

## What is top of plate height?

“Building plate height” means the vertical distance measured from the average level of the highest and lowest point of that portion of the lot covered by the building to the plate line of the exterior walls which is the horizontal plane where the exterior walls meet the roof rafters or trusses.

**How long are studs for a 9-foot wall?**

104 1/2 inches

The studs are 104 1/2 inches in homes with 9-foot walls.

**What is a standard wall height?**

8′

The standard wall height is usually 8′ but some luxury homes go up to approximately 9′ or 10′. You can have half-walls that define a space visually, or you can have a full-height wall that defines a space acoustically. Or you may choose to forgo the use of interior wall altogether.

### Are 9ft ceilings high?

What’s considered a high ceiling? Most older homes feature eight-foot ceilings, which was once considered the standard ceiling height to aim for. Newer homes, meanwhile, tend to come with nine-foot ceilings. But anything above the nine-foot mark is generally considered a high ceiling.

### Are 9-foot ceilings standard?

Today’s standard ceiling height is nine feet. Newer houses are often built with nine-foot ceilings on the first floor (and, sometimes, eight-foot ceilings on the second story). While many custom builders will assume that homeowners want nine-foot ceilings, don’t take it for granted.

**What is plate height?**

The height equivalent to a theoretical plate, as discussed above, is defined as the proportionality constant relating the standard deviation and the distance traveled. …

**What does plate high mean?**

You will often hear this stage called “Plate High” which in building terms means that the wall plate (the piece of timber which goes on top of the brickwork and holds the rafters and ceiling joists) is the next item to go on. …

#### How many studs do I need calculator?

Calculate the Studs

- Multiply the total wall length (in feet) by 0.75 (for 16-inch on-center stud spacing).
- Add three studs for each 90-degree corner.
- Add four studs for each 45-degree corner.
- Add two studs for each wall intersection (where another wall abuts the wall you are estimating).

#### What is the distance between studs?

The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.

**Are 9 foot ceilings standard?**

**Are 9 ft ceilings high?**

## How tall is the elevation of a building plan?

The plan is typically cut at a height of about 4 feet, but the architect drawing the plan may cut it at a different height. This means that you have an imaginary plane cutting through the building at an elevation of 4 feet above the floor.

## How tall is a 9’pre cut stud?

A 9′ pre-cut stud is 104-5/8″, which combined with a total of 3 plates, produces a 9′ wall. I would not count on EXACTLY 9′. quote]

**How big does a 9’wall need to be?**

A 9′ pre-cut stud is 104-5/8″, which combined with a total of 3 plates, produces a 9′ wall. I would not count on EXACTLY 9′. They buy pre-cut studs. A 9′ pre-cut stud is 104-5/8″, which combined with a total of 3 plates, produces a 9′ wall.

**What are the different types of elevation drawings?**

There are different types of Elevation Drawings: Section drawings are a specific type of drawing architects use to illustrate a building or portion of a building. A section is drawn from a vertical plane slicing through a building. This is as if you cut through a space vertically and stood directly in front looking straight at it.