What is factory jumper setting in hard disk?

You may have pins on the back of your hard drive that nothing is connected to. These pins are called jumpers, and are used to enable specific types of settings. You enable particular settings by placing a jumper shunt onto specific pins—creating an electrical circuit between them.

Is Maxtor owned by Seagate?

Seagate Technology, which makes computer hard drives used to store data, said Wednesday it agreed to acquire rival Maxtor Corp. for about $1.9 billion in stock.

What is CS enabled on a hard drive?

Cable select, also referred to by the acronym CS, is a disk drive jumper setting which automatically sets the priority of a disk drive by its position on its data cable. When cable select is enabled, the drive configures itself as a primary or secondary depending on its position in the drive chain.

How do you set up a jumper?

Jumper settings for 2 hard drives and 1 CD/DVD drive

  1. Set the first hard disk jumper as Master (alternatively, Cable Select selection can be used but set the second hard drive to Cable Select).
  2. Set the second hard disk jumper to Slave (use the Cable Select selection if Cable Select was set on the first hard drive).

What are jumper settings?

In electronics and particularly computing, a jumper is a short length of conductor used to close, open or bypass part of an electronic circuit. They are typically used to set up or configure printed circuit boards, such as the motherboards of computers. The process of setting a jumper is often called strapping.

Do SATA HDD need jumpers?

You don’t need a jumper pin on your SATA drive for desktops or servers manufactured after 2002. For older equipment, you can use a jumper on the pins to limit its data transfer rate so it can work smoothly with older, slower drives. A jumper pin is a rectangular connector that creates a circuit between two pins.

Who owns Maxtor?

Seagate Technology
Seagate Technology (US) Holdings, Inc
Maxtor/Parent organizations

Who bought Maxtor?

Seagate
Acquisition by Seagate In a deal worth nearly US$2 billion, Maxtor was acquired by its rival Seagate in 2006.

How do I unlock the power plan on Surface devices?

How to unlock Power Plans on Microsoft Surface Devices

  1. Type regedit to open Registry Editor.
  2. Go to “HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Power“
  3. Double click on “CsEnabled”
  4. Change Value data from “1″ to “0″
  5. Click OK.
  6. Restart your computer to apply these changes to your system.

What is IDE hard drive?

Integrated Drive Electronics (IDE) is a standard interface for connecting a motherboard to storage devices such as hard drives and CD-ROM/DVD drives. The original IDE had a 16-bit interface that connected two devices to a single-ribbon cable.

What should the jumper settings be for Seagate?

Master or single drive. If you are installing your Seagate hard drive as the only drive in the system or if it will be the primary boot drive for the system, the jumper should be set as Cable Select.

How do I jumper a Seagate Maxtor ATA drive?

If you are connecting the drive to an older system that has a pre-UDMA Mode 3 ATA controller, or you are connecting this to a cable with a slave device that doesn’t have a cable select jumper setting, jumper the drive as Master instead by putting a jumper on the first vertical set of pins closest to the data cable.

What’s the jumper setting on a Maxtor drive?

Maxtor (and Quantum) drives follow the jumper configuration noted below: The drive is configured at the factory for a cable select setting. This allows the drive to assume the proper role of master or slave based on the connector used on the cable (see the UltraATA cable figure above ).

Where is the blue connector on a Seagate hard drive?

The blue connector is for your host bus adapter (using a connector on your motherboard). The black connector at the other end is for your master device, usually the hard drive you boot from. The gray connector is for an optional slave device if you have a second hard drive.

By Guidelines