Contents
How much torque can a 1/2 breaker bar handle?
150 ft-lbs will break a 3/8″ drive usually and about 300 ft-lbs will break a 1/2″ drive. These are on regular breaker bars that are partially hollow and have the little ball in the space of the head to hold the socket. A SOLID 1/2″ heat treated impact rated drive anvil will go up to about 1200 ft-lbs.
How much torque can you get with a breaker bar?
At more than 3 feet long, a 40-inch breaker bar can produce a staggering 1,000 foot-pounds of torque. If a nut won’t come off under the pressure of a 40-inch bar, then it will probably need to be cut off.
Is it bad to use torque wrench as breaker bar?
Never use your torque wrench as a breaker bar—that’ll damage the torque mechanism. Carry it with kid gloves—a single fall can knock the accuracy off by as much as 30 percent. If you do drop it, get it recalibrated (calibration firms listed below) before using it again.
What is a 1/2 breaker bar used for?
Use this breaker bar to break loose stubborn nuts and bolts. Chrome vanadium steel construction gives this 1/2 in. breaker bar the edge on tough jobs. The drive end of the breaker bar has a 180° swivel to get the best angle on your work.
What size breaker bar is best?
The longer the bar is, the higher the leverage and subsequently, the higher the torque. Although length is necessary, there is generally no need to buy the longest break bar you can get your hands on; usually, 16 to 24 inches should be enough for general use.
Which breaker bar is best?
The Best Breaker Bar – 2021
- Neiko 00206A 1/2-Inch Drive Premium Breaker Bar, 24-Inch.
- GreatNeck BB18 1/2 Drive Breaker Bar, 18-Inch.
- Craftsman Flex Handle Breaker Bar Set, 3-Piece.
- EPAuto 1/2 Drive Breaker Bar, 24-Inch.
- TEKTON SBH00340 3/4 Drive Breaker Bar, 40-Inch.
How much torque can a human put on a bolt?
RE: Human Force to Turn a Bolt zakk: Assuming little body anchorage, I’d currently estimate a typical value of 170 N (38 lbf).
How much torque do you get hand?
Hand tight is on average about 2ft-lb.
Can you tighten bolts with a breaker bar?
You shouldn’t need to use a breaker bar for tightining down the lug nuts as it’s long enough. Yes, this is what a breaker bar is for; to give someone more leverage when loosening or tightening a bolt or nut. Although, I would not use a breaker bar to tighten lug nuts as it may cause damage.
What is the difference between a breaker bar and torque wrench?
The long handle on breaker bars compared to shorter wrenches allow a larger torque to be generated with the same amount of force. Also, the absence of a ratcheting mechanism makes a breaker bar considerably stronger than a ratchet. This allows greater torque to be applied to a fastener without the tool failing.
What torque wrench do I need for lug nuts?
The bigger the drive and the longer the handle, the more torque they can deliver. Most home mechanics will find that a torque wrench with a 1/2-inch drive and at least an 18-inch handle is the best choice for lug nuts, cylinder heads, suspension bushings, and other likely uses.
Which is better a breaker bar or a torque wrench?
As a breaker bar works using leverage to get a bolt off, it provides quite a large handle for you. So, it is very convenient to use no matter who you are. But with a torque wrench, things are different. A torque wrench is like a ratchet having a small handle compared to a breaker bar.
Where can I find the torque on a breaker?
Sometimes main breaker torque specs are labeled on the panel. There’s this publication from Schneider. But personally, I’d look at the breakers themselves: It’s very often printed on the face or side. Spend $75 to keep yourself safe.
What’s the torque on an allen wrench bolt?
In this day and age it is a lot easier to obtain the data than in pre-internet days. Most breakers with an Allen wrench bolt have the torque specs on them. Most of the SQ QO 200 amp stuff is 250 in lbs.
What’s the maximum torque a M24 can handle?
Standard torque figures for an M24 using a 12.9 grade fixing (strongest grade) is 926 lb ft http://electronicfilters.tpub.com/TM-10-4330-237-13P/css/TM-10-4330-237-13P_105.htm So I think it would reasonable to say that, even with a tiny factor of safety, a 1/2 drive extension should be able to handle 1000 lb ft