- 1 Which way does ONDULINE sheets go?
- 2 Can you stand on Onduline roofing?
- 3 Where can I find the instructions for the Form 1040EZ?
Which way does ONDULINE sheets go?
Start fixing sheets at the opposite end of the roof from the prevailing winds. Cut a sheet in half vertically and use to lay sheet courses in a broken bond pattern. Only use Onduline PP or Safetop nails on timber; check you have correct side and end sheet laps.
Can you bend bitumen roof sheets?
Don’t bend the Coroline Avoid bending the Coroline when you’re installing your roof; bends in the material can cause the roof to leak, and it won’t last as long as it should. Coroline fixings also have a specially designed waterproof cap that should ensure your roof lasts as long as possible.
What is the best way to cut bitumen roof sheets?
When cutting along the length of corrugated bitumen sheets, it is recommended to use a coarse bladed saw or Stanley knife. For width wise cutting, use either a circular saw or coarse bladed saw instead. If you are working with a more complex shape, tin snips provide better control over the cut.
Can you walk on corrugated bitumen sheets?
Personnel should walk on roofs only if this is absolutely necessary, and should use planks or ladders laid flat and supported by the roof purlins, in order to carry out maintenance and related work. …
How many screws do I need for an Onduline sheet?
Approximately 20 fasteners, nails or screws, must be fixed per sheet depending on the roof pitch. It is important to use Onduline fasteners as they are specifically designed, developed and manufactured to suit the roofing application requirements with ONDULINE sheets.
Can you stand on Onduline roofing?
Working on roofs can be a hazardous operation. Personnel should walk on roofs only if this is absolutely necessary, and should use planks or ladders laid flat and supported by the roof purlins, in order to carry out maintenance and related work.
How many screws do I need for an ONDULINE sheet?
How much do you overlap on ONDULINE sheets?
For roof pitches 10 to 15 degrees, ONDULINE sheet shall be supported by purlins with maximum width distance of 45 cm. For the end overlap, use minimum 30 cm. For the side overlap, use minimum 2 corrugations. For the end overlap, use minimum 20 cm.
How do you install a bitumen roof?
How to Install Torch-Down Modified Bitumen Roofing
- Ensure your flat roof is entirely clear of debris.
- Install heavy roofing felt with overtop your decking, old roof or insulation.
- Install drip edge flashing, and apply a primer so the roofing will adhere to it.
What’s the best way to fix Coroline sheets?
Fixing the Sheets Lay out the sheet, positioning square to the line of the eaves and verge. The sheet should overhang both verge and eaves. Take care that the overhang does not exceed 70mm in the case of the eaves. If cutting is necessary, cut Coroline sheets to length using a hand saw with a lubricating spray on the blade.
Where can I find the instructions for the Form 1040EZ?
For the latest information about developments related to Form 1040EZ and its instructions, such as legislation enacted after they were published, go to IRS.gov/Form1040EZ. FUTURE DEVELOPMENTS 2017 TAX CHANGES
How do you install Coroline on a roof?
If cutting is necessary, cut Coroline sheets to length using a hand saw with a lubricatingspray on the blade. Secure the sheet in place and ﬁx to the verge using Coroline ﬁxings at 100mm centres. Continue to install the sheet on the roof fixing through the crown of the corrugation.
Do you use Form 8962 or Form 1040EZ?
If you are claiming the premium tax credit, \le Form 8962 with Form 1040, 1040A, or 1040NR. DO NOT use Form 1040EZ. If you must reconcile advance payments of the premium tax credit, \le Form 8962 with Form 1040, 1040A, or 1040NR. DO NOT use Form 1040EZ.