What size saw for fret slots?
The saw you use, and the fret slot you create, needs to be properly fit to your fret wire for a snug, not too tight or too loose fit. Most fret saws will cut a slot that is . 023” wide which is perfect for most fret wire and is the starting point for great guitar fretwork.
What saw for cutting frets?
The Crimson Fine 10″ Guitar Fret Slotting Saw has a high-quality steel blade, a bright finished brass back and a rosewood handle and is designed as the perfect saw for cutting guitar frets. This saw has two holes in the blade allowing it to be used in conjunction with an adjustable depth stop.
What is the difference between a fret saw and a coping saw?
The fretsaw is a bow saw used for intricate cutting work which often incorporates tight curves. Although the coping saw is often used for similar work, the fretsaw is capable of much tighter radii and more delicate work. Unlike the coping saw, the blade has a fixed orientation in relation to the frame.
How deep should fret slots be cut?
The depth of the cut should be roughly half the thickness of the fingerboard itself. A correct fingerboard thickness should be roughly 1/4″, meaning your cut depth should roughly be 1/8″.
How wide should fret slots be?
Best Fret Wire in the World. Most fret profiles have a standard 0.020″ tang width. For installation, it is typically recommended that it is installed into a 0.023″ fret slot.
How deep should fret slots be?
The standard is 0.5 mm for regular frets and 0.63 mm for replacement frets. You can use a carpenter’s square to guide your fret saw (use the straight side of your fretboard).
How thick is a fret saw?
Fret Saw
| Overall length | 15-1/4″ | (387.35mm) |
|---|---|---|
| Cutting length | 10″ | (254mm) |
| Blade depth | 1-3/4″ | (44.45mm) |
Can you put a fret saw blade in a coping saw?
USING A FRET SAW. You wouldn’t want to use a fret saw for the heavy work of a coping saw. The thinner blades aren’t designed for heavy cutting. But it’s capable of much greater precision.
Can you use a jigsaw instead of a coping saw?
This makes them a must-have for any woodworker who wants to get the job done faster than with a hand-held coping saw. Jigsaws can cut cut wood of varying thickness and density, and when fitted with the correct blade, they can also cut steel, fiberglass, and drywall.
How accurate do fret slots need to be?
It must be very, very close or the instrument will sound like, well you know . . . When I cut my fret slots, I try to be accurate to within 1/64″. To my ear, that’s close enough. It had better be, because it’s about as close as I can cut them.
What fret size is best?
Short frets like the 6230, 6150, and 6130 are good for people who really like to feel to fingerboard when they play chords. Whereas, jumbo or medium-jumbo frets feel smoother, provide extra sustain, and can let you bend without exerting as much force.
What’s the best way to cut fretboard for ukulele?
If you just try to push it in straight, it usually tips over left or right before it actually goes in the slot, or at least that was the case with the narrow slots I cut with my dozuki saw. The method I ended up using was to hold one end of the fret, and squish the other end of it into the slot with pliers.
How is the taper cut on a ukulele?
The jig has an alignment pin that slots into the template to cut thin slots across the blank to take the frets. This system quickly creates accurate slots that ensure good intonation. Fig. 1, Fig. 2 Second, the taper is cut on a table saw jig that adjusts to cut each side accurately.
How do you make a bass ukulele out of wood?
It is simply made by cutting a U shape made from 3 bits of wood at right angles and putting a bit of snap off razor knife at the bottom to lock into the frets of the existing fretboard, which ensures that the frets I then cut in the top fretboard duplicate the ones in the bottom.
How does a jig work on a ukulele?
The normal saw blade has been replaced by a very thin blade and thick stiffeners. The jig has an alignment pin that slots into the template to cut thin slots across the blank to take the frets. This system quickly creates accurate slots that ensure good intonation.