Contents
How do I setup my HP c7000 enclosure?
HP c7000 Enclosure configuration
- Navigate to Enclosure Settings.
- Navigate to Active OA and click OK.
- Navigate to Active IPv4 and click OK.
- Choose proper value – static IP configuration or DHCP and click OK.
- Interface will direct you to Accept button.
- Now you can enter your IP address.
What is HP c7000 enclosure?
The HPE BladeSystem C7000 is a 10u high-density enclosure that supports up to 16 half-height blade servers. The enclosure provides shared power, cooling, and networking. It also offers easy management of shared resources and the ability to quickly scale as your business needs change.
Which feature optimizes power consumption by placing unneeded power supplies in standby mode?
Dynamic Power Saver mode
When enabled, Dynamic Power Saver mode saves power by running the required power supplies at a higher rate of utilization and putting unneeded power supplies in a standby mode.
How many blades occupy in c7000 chassis?
A BladeSystem c7000 enclosure holds up to 16 servers and/or up to 8 expansion blades (not exceeding 16 total blades) plus redundant network and storage interconnects.
How do I access onboard administrator?
Remote access to the Onboard Administrator
- Open a command-line window from a network-connected client.
- At the prompt, telnet to the IP address of the Onboard Administrator and press Enter.
- Enter a valid user name and press Enter.
- Enter a valid password and press Enter.
- Enter commands for the Onboard Administrator.
How do I access OA command line?
Execute the SHOW ALL command from either the OA GUI or the OA CLI as follows:
- OA GUI > Enclosure Settings > Configuration Scripts > SHOW ALL.
- OA CLI > Execute the following CLI command: SHOW ALL.
Is HPE OneView free?
The Standard version of HPE OneView is free to HPE clients, while the Advanced version is licensed for each physical server under the OneView management appliance.
What is mezzanine card in blade servers?
Server systems often comprise multiple server blades housed in a chassis and/or in standard rack mount. Expansion cards for blade servers may have a mezzanine design, in which the expansion card is inserted or installed parallel to the system board of the server.
How many Ru is c7000?
Class c7000 Enclosure A BladeSystem c7000 enclosure holds up to 16 server and/or storage blades plus redundant network and storage switches. It includes a shared, multi-terabit high-speed mid-plane for wire- once connectivity of server blades to network and shared storage.
What is OA in HP server?
The HP Onboard Administrator (OA) can generate a full inventory, status and configuration report of all the above components; this is the so called SHOW ALL report. The details below outline how this HP Onboard Administrator SHOW ALL report can be made.
How do I reset my HP c7000 enclosure?
The solution depends on the context:
- Cold reset (reboot) of the enclosure: Disconnect and reconnect all power cables until there are no power cables attached, wait a few seconds, then reattach them.
- Warm reset (reboot) of the enclosure:
- Reset to factory defaults:
What makes the HP BladeSystem c7000 enclosure redundant?
HP BladeSystem c7000 enclosure – side view The HP BladeSystem c7000 enclosure has a fully redundant design with redundant interconnections between servers and interconnect modules. The enclosure contains a NonStop signal midplane and a power backplane that have no active components.
How many blades are in a BladeSystem C class enclosure?
The enclosure is available with a choice of single- phase or three-phase power subsystem, depending on the data center power infrastructure. The c7000 enclosure can be populated with the following components: • Up to 8 full-height (FH) server blades or up to16 half-height (HH) server and/or storage blades per enclosure 3
What is the KVM port on the BladeSystem c7000?
The BladeSystem Onboard Administrator with KVM module adds the ability to directly connect the BladeSystem c7000 enclosure to a keyboard, mouse, monitor, or KVM switch through a VGA port.